How To Eliminate Rust From Shower Rod Guide For Cleaning Home Care

0

how to eliminate rust from shower rod guide for cleaning home care?

Because of all the moisture hovering around, Chrome shower rods fixtures made from similar material in a bathroom are likely to get rusty in time. There’s no need for sand unless the rust has not created a large gap or is extensive. All you need is to remove smaller rust spots that are typically present on an aluminum sheet that is actually a shower rod. Simply dip the water and vinegar into a solution to allow the reaction to take place.

Another way is to drain all the excess water completely out of the shower, but because minerals found in water leave behind lime and sediments, it does not allow it to pool on the floor. Although commercial cleaning chemicals can be purchased to eliminate stains and rust, natural remedies should work as well, so try whatever is convenient.

In the first place, why is it getting rusty?

The cause of rust over shower bars is iron oxide. It is a compound that is formed when iron atoms in the air react with oxygen atoms on the steel surface. When you stroke the rust with heat-generating aluminum foil, oxygen atoms leave the iron and therefore form aluminum oxide. From its original oxygen form, aluminium has a greater reduction tendency that results in rust migrating from the chrome shower rod to aluminium.

How to eliminate rust from shower rod guide for cleaning home care-Cleaning Steps.

Although for the sake of cleaning, you do not need to remove the entire shower rod, it is rather preferred so that it is possible to eliminate rust from the ends and mid joint! Check out the steps that follow below.

By simply wiping the shower rod with a moist rag, get rid of soap scup and other sediments. Use concentrated chemicals for difficult stains and deposits.

A sheet of aluminium foil should be carefully cut into small squares, each of the same shape and height. To accelerate the cleaning procedure, dip the pieces in warm water or in white vinegar. Vinegar; the strong presence of acetic acid eliminates rust and other stains more quickly than usual!

Now, gently rub these small aluminum squares over the rusted area; there is no need to apply pressure! You will immediately begin to see the results and the reaction will generate heat as you continue to work until the difference is significant. Continue rubbing until you feel the chrome progressively smoother, while the reaction will form aluminium oxide; a natural lubricant.

After eliminating rust, the next stage is to wipe with a clean and non-abrasive cloth off the rod. Apply a thin coating of automotive wax and everything to air-dry for the best results and shiny surface. Even if there are any small pits of rust present, wax would effectively cover them and prevent water from filtering further. This means that the very cause of rust will be eliminated!

Pretty helpful tip!

You are disturbed by the grazing sound of aluminum foil against the metal in the case; take steel wool as an alternative. Although it works in accordance with the same principle, the latter results are not as quick and perfect. For better and more accurate results, vinegar intensifies the propensity for rust-cutting. Don’t add salt or the reaction will generate hydrochloric acid when using vinegar as a rust cleaning agent; a highly concentrated acid that can damage different surfaces of the grout.

For extensive stains of rust

Once again, it would make a difference to apply vinegar to rust-affected areas, but it will not go away completely! If that happens, use sand paper to remove the rust and coat it with spray paint. Look for lubricants or corrosion-preventing chrome paint.

It is guaranteed that all the tips and details for a rust-free and clean shower will produce the best results. If the situation is beyond ordinary cleaning, call Dubai’s professional cleaning service.

Why does it work

The rust on your shower rods is iron oxide, a compound that forms as the iron atoms in the steel react to the oxygen atoms in the air. When you rub the rust with aluminum foil and generate heat, the oxygen atoms essentially give up the iron for the aluminum—which has a higher affinity to them—and form the aluminum oxide. Aluminum has a higher reduction potential in geek-speak, which means that it has a greater tendency to reduce oxygen from its original form. In short, the net result is that the rust essentially moves from the chrome shower rod to the aluminum rod.

How to do that – Step by Step Guide

This procedure does not require the downing of the shower rod, but you may want to remove rust from the ends or the joint in the middle.

Step 1:

Remove the surface of the dirt and the soap deposits by wiping the shower rod down with a damp cloth.

Step 2:

Cut the aluminum foil sheet into small squares and dip one of these squares in the water. You can also dip it in vinegar, which accelerates the cleaning process by dissolving the rust as you rub it.

Step 3:

Rub the aluminum foil lightly over the rusted area—you don’t need to press it hard. You’ll probably notice a difference right away, but as you keep rubbing and generating heat, the difference becomes more dramatic. Continue rubbing, and you’ll feel that the chrome is progressively smoother. This is the result of the formation of aluminum oxide, a natural lubricant.

Step 4:

Wipe off the rod with a clean rag after all the rust has been removed. Apply a thin coat of car wax; let it dry and buff it to a shiny finish. The wax covers the tiny pits left by the rust and prevents water from entering and causing the rust to recreate.

How to eliminate rust from shower rod guide for cleaning home care-Big Rust Spots

You can rub large rust spots with aluminum foil and make a difference, but the rust may not disappear completely. In that case, sand off the rust using 320-grit wet/dry sandpaper and coat the spot with chrome spray paint.

We will be happy to hear your thoughts

Leave a reply

Enable registration in settings - general